Welding Inspector
NDT.org Member Since: 2009
Added: 9/2/2009
Last Updated: 9/2/2009
Last Updated: 9/2/2009
To see contact info and over 12,000 resumes Get a Level II Subscription or Call (415) 796-6446.
Country:
Malaysia
Status:
I am willing to Travel.
I need a job as soon as possible.
I am willing to work overseas.
I prefer temp jobs.
I prefer permanent jobs.
I need a job as soon as possible.
I am willing to work overseas.
I prefer temp jobs.
I prefer permanent jobs.
Certifications
PCN Welding Inspector Level II
API 510 (attend course)
API 510 (attend course)
Education
Ruane-TATI, Malaysia
RSA Academy, Malaysia
RSA Academy, Malaysia
Experience
WORKING EXPERIENCES
May 2009 to June 2009
Company : NDE CONSULTANCY SDN. BHD.
Position : THIRD PARTY INSPECTOR (STATIC)
Project : OPTIMAL MAJOR TURNAROUND 2009
Client : Optimal Chemical (M) Sdn. Bhd.
DUTIES AND RESPONSIBILITIES
- Handle inspection for all of equipment such as pressure vessel, exchanger, and column.
- Note the ‘finding’ following the examination scheme setup in Optimal specification.
- Carry-out inspection based on history and previous report.
- Mark and report rejectable defects such as crack (linear indication), pin hole (rounded indication), major mechanical damage for repair or replacement.
- Carry out NDT works on suspicious area.
- Prepare photo report, external and internal checklist for inspection of equipment, pressure vessel examination report.
-Carried out RWSS to replace part or rebuilt weldment at defect area as per Optimal specifications.
- Make sure all of equipment be in better condition after turnaround.
September 2008 to May 2009
Company : GLOBAL INSPECTION SERVICES SDN. BHD.
Position : INDEPENDENT TESTING AGENCY INSPECTOR
Project : MARINA BAY SANDS Integrated resorts
Client : Alfasi Ltd / SANDS, Singapore
DUTIES AND RESPONSIBILITIES
- Review all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT) and submit preliminary approval procedures to client.
-Review inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Monitor/control welding works, consumables issued and welding parameters before, during, and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Note & report all abnormal finding and observe sign of corrosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before release load out to Singapore.
- Review all report such as Material traceability report, fit up report and visual report on compilation final document part by part.
January 2008 to July 2008
Company : KENCANA TORSCO BHD.
Position : QC INSPECTOR
Project : AZURITE FDPSO Development
Client : PROSAFE Ltd / MURPHY, Singapore
DUTIES AND RESPONSIBILITIES
- Obtain all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT), Inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Prepare/compile QC documents (MDR) for each project & maintain inspection record done on daily basis.
- Monitor/control welding works, consumables issued and welding parameters before, during , and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Carry out line check inspection and close all punch list on line pipe and structural to ensure its compliance to drawing.
- Note & report all abnormal finding and observe sign of leakage, corrosion, erosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before PWHT / Hydrotest.
November 2007 to December 2007
Company : NDE CONSULTANCY SDN. BHD.
Position : THIRD PARTY INSPECTOR (STATIC)
Project : OPTIMAL MAJOR TURNAROUND 2007
Client : Optimal Chemical (M) Sdn. Bhd.
DUTIES AND RESPONSIBILITIES
- Handle inspection for all of equipment such as pressure vessel, exchanger, and column.
- Note the ‘finding’ following the examination scheme setup in Optimal specification.
- Carry-out inspection based on history and previous report.
- Mark and report rejectable defects such as crack (linear indication), pin hole (rounded indication), major mechanical damage for repair or replacement.
- Carry out NDT works on suspicious area.
- Prepare photo report, external and internal checklist for inspection of equipment, pressure vessel examination report.
- Make sure all of equipment be in better condition after turnaround.
January 2007 to September 2007
Company : MUSHTARI ENGINEERING AND TRADING SDN. BHD
Position : QC Inspector
Project : AGRU Backflow Protection For GPP2
Client : Petronas Gas Berhad
DUTIES AND RESPONSIBILITIES
- Mark-up joint and spool number on the drawing.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Check any fabrication work for layout / dimensional / fit-up and visual inspection as per drawing and specification.
- Carry out line check inspection and close all punch list on line pipe to ensure its compliance to drawing.
- Review and update isometric drawing according to line service.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Review RT films, liaise with inspection party for inspection and reporting.
- Perform final inspection, final visual and dimensional checks before PWHT / hydro test.
- Prepare and compile final QC documentation (MDR) for submission to client (PGB).
June 2004 to December 2006
Company : VASTALUX SDN. BHD
Position : QC Inspector
Project : Handled several projects carried out by Vastalux Sdn. Bhd. :-
- Provision Of Integrated Topside Major Maintenance (TMM)
Services for Petronas Carigali Platform
Client : Petronas Carigali
- Provision Of Flowline Hook-Up & Commissioning Services For
CKA and CKC Platform
Client : Carigali Triton Operating Company
- Replacement Flowline Header at DDP-A and DDP-C Platform
Client : Petronas Carigali
- Replacement Corroded Piping at Dulang D and Dulang B
Platform
Client : Petronas Carigali
DUTIES AND RESPONSIBILITIES
- Obtain all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT), Inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Prepare/compile QC documents (MDR) for each project & maintain inspection record done on daily basis.
- Monitor/control welding works, consumables issued and welding parameters before, during , and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Check ferrite content and Control temperature for Duplex material and visual inspection.
- Carry out line check inspection and close all punch list on line pipe to ensure its compliance to drawing.
- Note & report all abnormal finding and observe sign of leakage, corrosion, erosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before PWHT / Hydrotest.
- Witness air leak test, hydrotest (Test Package) and prepare test report.
- Prepare Release Note and Material Equipment Inspection Verification.
May 2009 to June 2009
Company : NDE CONSULTANCY SDN. BHD.
Position : THIRD PARTY INSPECTOR (STATIC)
Project : OPTIMAL MAJOR TURNAROUND 2009
Client : Optimal Chemical (M) Sdn. Bhd.
DUTIES AND RESPONSIBILITIES
- Handle inspection for all of equipment such as pressure vessel, exchanger, and column.
- Note the ‘finding’ following the examination scheme setup in Optimal specification.
- Carry-out inspection based on history and previous report.
- Mark and report rejectable defects such as crack (linear indication), pin hole (rounded indication), major mechanical damage for repair or replacement.
- Carry out NDT works on suspicious area.
- Prepare photo report, external and internal checklist for inspection of equipment, pressure vessel examination report.
-Carried out RWSS to replace part or rebuilt weldment at defect area as per Optimal specifications.
- Make sure all of equipment be in better condition after turnaround.
September 2008 to May 2009
Company : GLOBAL INSPECTION SERVICES SDN. BHD.
Position : INDEPENDENT TESTING AGENCY INSPECTOR
Project : MARINA BAY SANDS Integrated resorts
Client : Alfasi Ltd / SANDS, Singapore
DUTIES AND RESPONSIBILITIES
- Review all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT) and submit preliminary approval procedures to client.
-Review inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Monitor/control welding works, consumables issued and welding parameters before, during, and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Note & report all abnormal finding and observe sign of corrosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before release load out to Singapore.
- Review all report such as Material traceability report, fit up report and visual report on compilation final document part by part.
January 2008 to July 2008
Company : KENCANA TORSCO BHD.
Position : QC INSPECTOR
Project : AZURITE FDPSO Development
Client : PROSAFE Ltd / MURPHY, Singapore
DUTIES AND RESPONSIBILITIES
- Obtain all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT), Inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Prepare/compile QC documents (MDR) for each project & maintain inspection record done on daily basis.
- Monitor/control welding works, consumables issued and welding parameters before, during , and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Carry out line check inspection and close all punch list on line pipe and structural to ensure its compliance to drawing.
- Note & report all abnormal finding and observe sign of leakage, corrosion, erosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before PWHT / Hydrotest.
November 2007 to December 2007
Company : NDE CONSULTANCY SDN. BHD.
Position : THIRD PARTY INSPECTOR (STATIC)
Project : OPTIMAL MAJOR TURNAROUND 2007
Client : Optimal Chemical (M) Sdn. Bhd.
DUTIES AND RESPONSIBILITIES
- Handle inspection for all of equipment such as pressure vessel, exchanger, and column.
- Note the ‘finding’ following the examination scheme setup in Optimal specification.
- Carry-out inspection based on history and previous report.
- Mark and report rejectable defects such as crack (linear indication), pin hole (rounded indication), major mechanical damage for repair or replacement.
- Carry out NDT works on suspicious area.
- Prepare photo report, external and internal checklist for inspection of equipment, pressure vessel examination report.
- Make sure all of equipment be in better condition after turnaround.
January 2007 to September 2007
Company : MUSHTARI ENGINEERING AND TRADING SDN. BHD
Position : QC Inspector
Project : AGRU Backflow Protection For GPP2
Client : Petronas Gas Berhad
DUTIES AND RESPONSIBILITIES
- Mark-up joint and spool number on the drawing.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Check any fabrication work for layout / dimensional / fit-up and visual inspection as per drawing and specification.
- Carry out line check inspection and close all punch list on line pipe to ensure its compliance to drawing.
- Review and update isometric drawing according to line service.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Review RT films, liaise with inspection party for inspection and reporting.
- Perform final inspection, final visual and dimensional checks before PWHT / hydro test.
- Prepare and compile final QC documentation (MDR) for submission to client (PGB).
June 2004 to December 2006
Company : VASTALUX SDN. BHD
Position : QC Inspector
Project : Handled several projects carried out by Vastalux Sdn. Bhd. :-
- Provision Of Integrated Topside Major Maintenance (TMM)
Services for Petronas Carigali Platform
Client : Petronas Carigali
- Provision Of Flowline Hook-Up & Commissioning Services For
CKA and CKC Platform
Client : Carigali Triton Operating Company
- Replacement Flowline Header at DDP-A and DDP-C Platform
Client : Petronas Carigali
- Replacement Corroded Piping at Dulang D and Dulang B
Platform
Client : Petronas Carigali
DUTIES AND RESPONSIBILITIES
- Obtain all relevant documents such as specification and codes, welding procedures (WPS), welding procedures qualification test (WPQT), Inspection test program (ITP), drawing and other approved procedure by client.
- Perform incoming material inspection for visual, dimensional and verification of mill certificates and transfer identification marks as applicable.
- Prepare/compile QC documents (MDR) for each project & maintain inspection record done on daily basis.
- Monitor/control welding works, consumables issued and welding parameters before, during , and after of welding as per ITP and procedure.
- Check any fabrication work for layout / dimensional / fit-up / and visual inspection as per drawing and specification.
- Check ferrite content and Control temperature for Duplex material and visual inspection.
- Carry out line check inspection and close all punch list on line pipe to ensure its compliance to drawing.
- Note & report all abnormal finding and observe sign of leakage, corrosion, erosion and distortion.
- Monitor NDT inspection & review NDT report to ensure in accordance to code requirements.
- Perform final inspection, final visual, and dimensional checks before PWHT / Hydrotest.
- Witness air leak test, hydrotest (Test Package) and prepare test report.
- Prepare Release Note and Material Equipment Inspection Verification.
Comments
No Comments
