Queen City High School
studied basic corses / Ag. metal fab and Ag. mechanics
Gruaduated / June 2009

Experienced in operating mig welder, ark welder. I am experienced in operating/using, skill saws, table saws,jig saws,nail guns, sawzall, drills,drill presses, tork wrenches, mic odomer, caliper, open and boxed in wrenches, metric and standard, sockets,ratches, di grinder, cut off saw, air ratches, impacts, dial calipers, timing light, pullers and installers, bearing separators, multi meter, scanner, freon recovery R12 and 134A, coolent flush, plasma cutter, motor vac. I am experienced in replacing rear wheel drive and four wheel drive transmissions, front wheel drive transmissions in many different makes and modles. rebuilding transmissions, removing and installing plugs, plug wires, caps, rotor buttons, water pumps,starters,alternators. experienced in complete rebuilt 14 bolt one ton rear end in a dana 44 1/2 ton front end, 9" ford rear end on a 87 jeep CJ7, complete rebuild of a dana 30 front end, removing engines and replacing all gaskets and installing in chevy 350. I am experienced building bob wire fences, streching bob wire, driving t-post, digging holes for fence post using shovels and 3 point auger, cleaning fence rolls. I can operate a forklift, a 100 horse tractor with front end loader, a bush hog, disk, and manure-spreader.

Work History

June 2007-Dec 2007
Hurdle Tracor Repair
Atlanta, Tx.75551

Meachanic
Preformed mechanical repairs on Ford tractors ranging from Ford 2000 thr 7000, removing and replacing clutches, pressure plates, throw out bearings and polite bearings, head gaskets, removing and replacing seals in 3 point hydraulic system, removing and replacing freeze plug on back of head, PTO shaft seals, removing and replacing wet and dry brakes, power steering hoses, replacing hyrdraulic assist cylinders, radiators. Kobta 30 horse tractor, removed engine clutch and tore down to block. Massy Fergerson 38 horse to 100 horse tractors removing and replacing clutches, pressure plate throw out bearing and polite bearing, starters, PTO shaft seals, oil pump. John Deere 50 horse 100 horse tractors, head gasket on 6 cylinder, removes and replaced gas tank, 3 point hydraulic seals, wet brakes, hydraulic hoses, power steering hoses, water hoses, water pump to be reworked, starte buttons.

Nov 2008-Dec 2008
Karnack Tx
TNT Railcar Services, Inc.

Operate a mig welder with flux core .45 with airgon gaswelding 1/4" steel up to 1/2" steel using single pss bead and horseshoeing, I can weld overhead, uphill, downhill, vertical and horizontal. Operate an ark welder 7018 electrode and 6011 electrode, welding overhead and hownhill, weld 1/4" steel, inside tank cars, welding up stress cracks, tore down trucks, brake pads, load springs and put them back together, applied roof seal ontop of box cars, painted inside of box cars, used blow torch, grinder 4" and 9", operated and ran forklift.

Sep 2008-Nov 2008
Atlanta Tx
Rockford Corporation

Oiler
Operated Cat track hoe 330 and 345, digging ditches 12" deep x 14' wide and back filled. Operated John Deere D6 and D7 dozier, blading the road and back filling ditches. Operated water pump with 3" hoses and 6" hoses pumping water out of ditches through a slit bag. I would reheat 42" pipe with propane torch for the labors, i stackes skids under pipes, hookes up slings as basket sling as choker ling, cutting holes with torch in sheet piling for the operator.

Mar 2007-June 2007
Raines Auto Center
Atlanta Tx

Maintenance
Mount, balance and rotated wheels, oil changes, pan and filter transmission fluid change, removed and replaced alternators, front brakes, assisted in front end alignments, lawn care, amintained shop, swept and mooped the whole shop, cleaned the restroom, office, and waitin area daily, stocked shop with supplies.

Dec 2009-Present
Cass County Cars
Atlanta Tx

Detail and maintain services for vehicles for resale. Oil changes, stain removal, engine maintenance etc.