NDT Technician (2nd Shift)
Posted: 2/29/2016 2:09:21 PM
This job is closed
NDT.org Job Number:
57321
* Please reference NDT.org Job Number on all correspondence
Contact:
Jeremy Tomsic
Phone:
440-701-1171
Company:
Component Repair Technologies
State:
OH Ohio
Contact:
Jeremy Tomsic
Country:
United States
Length:
Full-time (50-55 hours/Week)
Pay:
20-26/hour
Benefits to working at CRT:
◦Clean work environment
◦Competitive pay with $2-3 shift premiums
◦Fully paid health insurance
◦Profit sharing bonuses
◦Paid tuition for job-related courses and programs on-site and at area colleges
◦State-sponsored apprenticeship programs
◦Countless internal promotional opportunities
CRT is committed to providing a safe and healthy workplace and promoting the health and well-being of its employees. It is the Company’s policy to only hire individuals who do not use tobacco products. In addition to drug and alcohol testing all candidates will be screened for nicotine prior to hire. Employment opportunities at CRT are open to all qualified applicants solely on the basis of their job-related experience, knowledge, skills and abilities. CRT complies with all applicable federal, state and local laws with regard to equal employment opportunity.
Follow the link below to get an inside look at CRT!
http://www.youtube.com/watch?v=g7_pVOxhDBs
FUNCTIONAL RESPONSIBILITY:
Under general supervision prepares set ups and prepares parts for non-destructive tests. Under the guidance of a Certified Level III, performs fluorescent penetrant, magnetic particle, and or pressure test inspections on aircraft engine components. Non-Destructive test include but are not limited to the following procedures.
SPECIFIC RESPONSIBILITIES:
FPI TEST
1. Verify that parts are properly pre-cleaned for FPI; may perform pre-cleaning when required.
2. Maintain FPI equipment for effective operation, performing system tests daily, weekly or as required to specifications.
3. Apply penetrant onto the part or test area to be inspected using FPI equipment, remove, dry, and develop.
4. Visually inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
5. Special attention must be given to ensure the integrity of any area of the part that may have been subjected to corrosive conditions.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
MPI TEST
1. Verify that parts are properly pre-cleaned for MPI; may perform pre-cleaning when required.
2. Maintain MPI equipment for effective operation, perform system tests daily, weekly or as required to specifications.
3. Process parts on the wet horizontal mag unit using the continuous method of inspection.
4. Visually inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
MPI TEST (CONTINUED)
5. Special attention must be given to ensure the integrity of any area of the part that may have been subjected to corrosive conditions.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
PRESSURE TEST
1. Set up parts for pressure testing under water.
2. Securely plug all openings except the air intake port.
3. Check water in test tank for proper temperature and Ph verification.
4. Apply pressure and inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
5. Inspect for air leaks over the time interval specified.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
◦Clean work environment
◦Competitive pay with $2-3 shift premiums
◦Fully paid health insurance
◦Profit sharing bonuses
◦Paid tuition for job-related courses and programs on-site and at area colleges
◦State-sponsored apprenticeship programs
◦Countless internal promotional opportunities
CRT is committed to providing a safe and healthy workplace and promoting the health and well-being of its employees. It is the Company’s policy to only hire individuals who do not use tobacco products. In addition to drug and alcohol testing all candidates will be screened for nicotine prior to hire. Employment opportunities at CRT are open to all qualified applicants solely on the basis of their job-related experience, knowledge, skills and abilities. CRT complies with all applicable federal, state and local laws with regard to equal employment opportunity.
Follow the link below to get an inside look at CRT!
http://www.youtube.com/watch?v=g7_pVOxhDBs
FUNCTIONAL RESPONSIBILITY:
Under general supervision prepares set ups and prepares parts for non-destructive tests. Under the guidance of a Certified Level III, performs fluorescent penetrant, magnetic particle, and or pressure test inspections on aircraft engine components. Non-Destructive test include but are not limited to the following procedures.
SPECIFIC RESPONSIBILITIES:
FPI TEST
1. Verify that parts are properly pre-cleaned for FPI; may perform pre-cleaning when required.
2. Maintain FPI equipment for effective operation, performing system tests daily, weekly or as required to specifications.
3. Apply penetrant onto the part or test area to be inspected using FPI equipment, remove, dry, and develop.
4. Visually inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
5. Special attention must be given to ensure the integrity of any area of the part that may have been subjected to corrosive conditions.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
MPI TEST
1. Verify that parts are properly pre-cleaned for MPI; may perform pre-cleaning when required.
2. Maintain MPI equipment for effective operation, perform system tests daily, weekly or as required to specifications.
3. Process parts on the wet horizontal mag unit using the continuous method of inspection.
4. Visually inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
MPI TEST (CONTINUED)
5. Special attention must be given to ensure the integrity of any area of the part that may have been subjected to corrosive conditions.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
PRESSURE TEST
1. Set up parts for pressure testing under water.
2. Securely plug all openings except the air intake port.
3. Check water in test tank for proper temperature and Ph verification.
4. Apply pressure and inspect as specified by FAA-approved documentation including Manufacturer, Customer and customized CRT procedures.
5. Inspect for air leaks over the time interval specified.
6. Record all results clearly and accurately on an inspection form and in the proper log.
7. Report any deviations to the appropriate Product Leader.
Skills:
QUALIFICATIONS:
1.Must meet all the general qualifications required of all CRT employees.
2.Must have a high school diploma or the equivalent.
3.Must complete classroom and on the job training as outlined in the CRT operating procedures manual.
4.Must be able to pass the written and practical examinations required for certification.
5.Minimum of 6 months of OJT and experience under close supervision of a qualified NDT operator.
6.Demonstrated skills, ability and careful attention to precise details of all testing procedures and record keeping.
7.Willingness and ability to learn and progress to higher levels of certification and responsibility.
8.Current ASNT Level II (PT/MT) certification required.
1.Must meet all the general qualifications required of all CRT employees.
2.Must have a high school diploma or the equivalent.
3.Must complete classroom and on the job training as outlined in the CRT operating procedures manual.
4.Must be able to pass the written and practical examinations required for certification.
5.Minimum of 6 months of OJT and experience under close supervision of a qualified NDT operator.
6.Demonstrated skills, ability and careful attention to precise details of all testing procedures and record keeping.
7.Willingness and ability to learn and progress to higher levels of certification and responsibility.
8.Current ASNT Level II (PT/MT) certification required.
